Skip to content
-
-
-
350,66 € (sis. KM)
- P2BN 40M-SRB-TRE Pillow block roller bearing unit, metric series Roller bearing units are robust, ready-to-mount units that are lubricated and sealed at the factory for maximum service life. Pillow (plummer) block units can support rotating shafts while standing on a flat surface, or hanging on a wall or ceiling. The SKF SwiftLock combines easy mounting and a concentric tight fit…
- Lisa korvi
-
-
-
56,30 € (sis. KM)
- KM 24 Lock nut with metric thread, for locking by lock washer KM and KML lock nuts are used to locate bearings onto a shaft. They have metric threads and four equally spaced slots located around their circumference to accommodate a spanner. They should be locked by a lock washer to prevent unintentional loosening. KM and KML lock nuts can…
- Lisa korvi
-
-
-
-
13,08 € (sis. KM)
- 51103 Single direction thrust ball bearing Single direction thrust ball bearings can accommodate axial loads in one direction. They must not be subjected to any radial load. Their separable components facilitate mounting/dismounting and maintenance inspections. Many of the components are interchangeable. The shaft washers have a ground bore that enables an interference fit. Separable design facilitates mounting/dismounting and maintenance inspections…
- Lisa korvi
-
-
-
26,86 € (sis. KM)
- H 310 Adapter sleeve with KM lock nut and MB lock washer, metric dimensions Adapter sleeves are the most commonly used components for locating bearings with a tapered bore onto a cylindrical seat as they can be used on plain shafts or stepped shafts. They are slit and are supplied complete with a KM lock nut and a MB lock…
- Lisa korvi
-
-
-
47,06 € (sis. KM)
- 2210 EKTN9/C3 Self-aligning ball bearing with tapered bore Self-aligning ball bearings, with a tapered bore, have two rows of balls, a common sphered raceway in the outer ring and two deep uninterrupted raceway grooves in the inner ring. They are insensitive to angular misalignment of the shaft relative to the housing, which can be caused, for example, by shaft deflection.…
- Lisa korvi
-
-
-
555,50 € (sis. KM)
- 6315/C3VL0241 INSOCOAT® deep groove ball bearing INSOCOAT single row deep groove ball bearings feature an electrically insulating coating on the outside surfaces of either the inner or outer bearing ring. This keeps stray electric currents from passing through the bearings, protecting them against electrical erosion damage and helping prevent lubricant degradation resulting from electric current discharge. As with deep groove…
- Lisa korvi
-
-
-
18,33 € (sis. KM)
- RIS 209 A Rubber seating ring for insert bearing Rubber seating rings in the RIS 2 series are primarily intended to cushion insert bearings in pressed steel pillow (plummer) block housings. Located between the bearing outer ring and housing bore, they dampen vibration and noise and enable the bearings to be displaced slightly in their housings and to accommodate minor…
- Lisa korvi
-
-
-
6,88 € (sis. KM)
- HK 1612 Drawn cup needle roller bearing with open ends Drawn cup needle roller bearings are typically used in applications where the housing bore cannot be used as a raceway for a needle roller and cage assembly, but where a very compact and economical bearing arrangement is required. Owing to their large number of rollers, the bearings have a high…
- Lisa korvi
-
-
-
25,48 € (sis. KM)
- 16009/C3 Deep groove ball bearing Single row deep groove ball bearings are particularly versatile, have low friction and are optimized for low noise and low vibration, which enables high rotational speeds. They accommodate radial and axial loads in both directions, are easy to mount, and require less maintenance than many other bearing types. Simple, versatile and robust design Low friction…
- Lisa korvi
-
-
-
43,40 € (sis. KM)
- TSN 213 A V-ring seal V-ring seals consist of a V-ring and a sheet steel sealing washer with a vulcanized rubber lip. The rubber lip fits into the seal groove in the housing. The washer is protected against corrosion. The seals are used to protect bearings from contamination or as secondary seals to protect primary seals in highly contaminated environments.…
- Lisa korvi
-
-
-
52,33 € (sis. KM)
- 4SPB140TB Wedge belt pulley, taper bushed Wedge belt pulleys are designed to be used with wedge belts. They are available with one or several grooves, enabling multiple belts to run in parallel. The pulleys are easily mounted on the shafts using the appropriate taper bushings. Manufactured according to international standards Phosphate-coated for corrosion resistance Statically balanced (dynamic balancing available on…
- Lisa korvi
