Alates 60€ ostudele on transport tasuta!
Kõikidele registreeritud kasutajatele rakendub allahindlus 12%, ostudel üle 122€ on lisaallahindlus kõigile 5% (kokku 17%).
Toodete otsimine/leidmine:
- Laagrid mõõdu järgi: _ X _ X _ nt
17 X 40 X 12. Kuvatakse kõik selles mõõdus olevad laagrid. - Tootekoodi järgi: 6204, nt
6204-2RS. Kuvatakse tooted, mis algavad selle koodiga ja sisalduvad toote nimetuses. - Kaelustihend/o-rõngad: _X_X_X, nt
10X22X7kaelustihenditel täpne tulemus; 10 X 22 X 7 kuvatakse tooted, kus on vähemalt üks mõõtudest; 30 X 3/7, 94 X 1,78 o-rõngastel. - Kategooriad: nt Laagrid > filtreeri “Filtrid” alt kuullaagrid. Kuvatakse kõik kuullaagrid.
- Rihmad: kuvatakse tootekoodi ja/või mõõdu alusel, nt
17 X 875; SPA950
-
LAAGRIKORPUS SY 508 M SKF
- 29,14 € (sis. KM)
- SY 508 M Pillow block housing for insert bearings, cast iron, ISO standards Pillow (plummer) block housings are designed to accommodate an insert bearing. The cast iron housings are strong, stiff and cost-effective. They are suitable for most applications and can be bolted directly to a support surface. Accommodate heavy loads in different directions High degree of stiffness Narrow design
- Lisa korvi
-
KIILRIHM HAMMASTATUD XPA 2650Lw EPDM SKF
- 35,86 € (sis. KM)
- PHG XPA2650EP Cogged raw-edge wedge belt Belts provide a very efficient and cost-effective method for transmitting power from prime movers to driven machines. These raw-edge wedge belts have cogs on their inside that enable the belts to flex around smaller pulleys. Without fabric covering their flanks, raw-edge belts can provide a higher friction and a minimized loss of power through…
- Lisa korvi
-
ENERGIATÕHUS ÜHEREALINE KUULLAAGER METALLIKATETEGA E2 6002-2Z/C3 15X32X9 SKF
- 5,77 € (sis. KM)
- SKF Energy Efficient (E2) radiaalkuullaagrid SKF E2 radiaalkuullaagrid tagavad rohkem kui kahekordse kasutusea, vähendades samal ajal energiakulu. Konstruktsiooni täiustused vähendavad laagrite hõõrdekadusid vähemalt 30% võrra võrreldes sama suure SKF Explorer seeria laagriga. Selle tulemuseks on energiasääst.
- Lisa korvi
-
KAELUSTIHEND 50 X 62 X 7 HMSA10 V VITON SKF
- 18,40 € (sis. KM)
- 50X62X7 HMSA10 V Radial shaft seal with rubber outside diameter and single sealing lip, for oil or grease Radial shaft seals are used between rotating and stationary machine components, or between components in relative motion. HMSA10 seals are designed with a rubber outside diameter. They have a conventional sealing lip made of elastomer. A garter spring in the seal and…
- Lisa korvi
-
O-RÕNGAS 19,20 X 3,0 NBR70 SKF
- 0,67 € (sis. KM)
- OR 19.2X3.0-N70 O-ring O-rings maintain sealing contact force due to their radial or axial deformation within the seal housing between two components. SKF supplies O-rings in a wide range of sizes and different materials, which make them appropriate for a wide variety of operating conditions and applications. They are easy to install and enable a simple and cost-effective seal housing…
- Lisa korvi
-
HAMMASRIHM HTD 177 3M L-9MM Z-59 OPTIBELT OMEGA
- 12,42 € (sis. KM)
- 177-3M-9 HTD belt Belts provide a very efficient and cost-effective method for transmitting power from prime movers to driven machines. High torque drive (HTD) timing belts have teeth that interlock with the corresponding grooves on the pulleys to ensure a constant speed ratio. The low stretch glass fibre cords guarantee excellent dimensional stability. The oil and heat resistant neoprene rubber…
- Lisa korvi
-
SDBT-MSX-1L-PU-E-0.3-N-M8 Lähestumisandur FESTO
- 48,45 € (sis. KM)
- Lisa korvi
-
HAMMASRIHM PU T2,5-330 L-10MM Z-132 STRONGBELT IMPULS
- 21,28 € (sis. KM)
- T2.5-330-10 Metric timing belt, T section Belts provide a very efficient and cost-effective method for transmitting power from prime movers to driven machines. Metric timing belts have teeth that interlock with the corresponding grooves on the pulleys to ensure a constant speed ratio. The combination of high tensile steel cords and a wear-resistant polyurethane rubber cushion provides dimensionally stable and…
- Lisa korvi
-
HAMMASRIHM HTD 825 5M L-25MM Z-165 OPTIBELT OMEGA
- 36,98 € (sis. KM)
- 825-5M-25 HTD belt Belts provide a very efficient and cost-effective method for transmitting power from prime movers to driven machines. High torque drive (HTD) timing belts have teeth that interlock with the corresponding grooves on the pulleys to ensure a constant speed ratio. The low stretch glass fibre cords guarantee excellent dimensional stability. The oil and heat resistant neoprene rubber…
- Lisa korvi
-
MANOMEETER MA-40-10-G1/4-EN FESTO
- 18,09 € (sis. KM)
- Lisa korvi
-
KOMPAKTSILINDER ADN-32-40-A-PPS-A FESTO
- 106,76 € (sis. KM)
- Lisa korvi
-
LIIGENDLAAGER d-90MM GE 90 ES
- 91,82 € (sis. KM)
- Lisa korvi
